.

Feked Classic Bike Parts
The Old Racing Stables, Nine Yews, Cranborne, Dorset BH21 5PW, UK

.
.
.

Useful & Interesting

SHIPPING COSTS SHIPPING COSTS

Engine Lower

plate4016G-B13
£8.95 (£10.74 inc VAT)
OEM: 70-4016G, E4016G
Triumph Patent Plate - TRW Side Valve Models Brass timing cover triangular name plate for 500cc side valve twins. Supplied with 3 brass  hammer drive...
+

bearing205c-F4
£8.95 (£10.74 inc VAT)
OEM: 65-2045, T34
BSA Crankshaft Main Drive Side Ball Bearing - B and M Group Models Circa 1946-63 Outer drive side ball bearing - correct fitment on B31, B32, B33, B34,...
+

bearing205g-F4
£8.95 (£10.74 inc VAT)
OEM: 57-1070, T1070
Triumph Gearbox Mainshaft High Gear Bearing - T15 and T20 Models From 1956 Onwards Left hand gearbox mainshaft ball bearing - correct fitment on T15 and...
+

pipe5290-B13
£9.45 (£11.34 inc VAT)
OEM: 83-5290, F15290
Triumph Breather Hose 'T' Piece - 750cc Unit Twins - 1974 Onwards Crankcase breather pipe connector for T140, TR7 Models from 1974 onwards. Small pipe...
+

enginestud-9495-B13
£9.45 (£11.34 inc VAT)
OEM: 70-9495, E9495
Triumph Alternator Mounting Stator Stud - Unit 350/500cc Models - Circa 1969-72 Stator stud - correct fitment on T90 and T100 models circa 1969-72. Three...
+

filt059-B3
£9.95 (£11.94 inc VAT)
OEM: 70-9979, E9979
BSA B25, B50 Oil Sump Filter Gauze Stainless Steel Oil sump filter. 9mm hole OEM: 70-9979, E9979
+

seal355-B7
£9.95 (£11.94 inc VAT)
OEM: 40-25, 40-0025, 41-3054, 40-977, 40-0977, 40-679, 40-0679, 57-2641, 40-243, 40-0243, 40-3281, 70-4568, E4568
Oil Seal Set - Engine and Gearbox To suit BSA B25, C25, B44 1967-1972, B50 1971-1972 Contains: Contact point (camshaft) seals, Clutch back plate seal,...
+

bear025-F4
£9.95 (£11.94 inc VAT)
Ball Bearing RLS5 - 4203-2RS Range of uses including wheel bearing, transmission and engine bearing. OD: 40mm ID: 17mm Width: 16mm
+

washer4075-B13
£9.95 (£11.94 inc VAT)
OEM: 42-4075
BSA Gearbox Locking Washer - 42-4075 Used on the BSA A10 and A7 gearbox to frame. OEM: 42-4075
+

pipe4813
£9.95 (£11.94 inc VAT)
OEM: 83-4813, F14813
Triumph 'D' Type Crankcase Breather Hose/Pipe - T140/TR7 - 1974-78 This hose runs along the rear mudguard after the 'T' piece As fitted to 750cc T140/TR7...
+

pipe7387-B2
£9.95 (£11.94 inc VAT)
OEM: 83-7387
Triumph 'D' Type Rear Mudguard Breather Hose/Pipe - T140/TR7 1977 Onwards Silver coloured 'D' shaped pipe Approximately 52" (132cm) ID: 1/2" (13mm) OD:...
+

nut1007-B18
£9.95 (£11.94 inc VAT)
OEM: 71-1007, E11007
Triumph Inlet Camshaft Oil Pump Drive Nut - 500/650/750cc Twins - 1970-83 Correct fitment for  650 and 750 Twins from 1970-1983. Also fits Triumph 500...
+

c/s-tube3903-B13
£9.95 (£11.94 inc VAT)
OEM: 70-3903, E3903, 68-0185, 68-185
Triumph/BSA Crankshaft Sludge / Oil Tube - 500/650/750cc Twins Circa 1959-82 Crankshaft oil tube, sludge trap - correct fitment on pre unit T100, 6T,...
+

nut5664-B13
£9.95 (£11.94 inc VAT)
OEM: 15-5664
BSA Gearbox Adjuster Nut - A, B and M Group - Rigid, Plunger and Swinging Arm Models Gearbox adjusting bolt nut - correct fitment on swinging arm A7,...
+

bigend6488
£9.95 (£11.94 inc VAT)
OEM: 70-6488, E6488
Triumph T20 Connecting Rod Big End Bush - SH and SM Tiger Cub Models - Circa 1964-68 Correct fitment on later Tiger Cub models from  engine number 99720....
+

seal351-B7
£9.95 (£11.94 inc VAT)
OEM: 90-0749, 90-0147, 89-3006, 86-8769
Oil Seal Set - Engine and Gearbox - BSA Bantam D10 and D14 Models - Circa 1967-71 Suitable for three or four speed D10 and D14 Bantam models. Kit...
+

c/s-tube3999-B13
£9.95 (£11.94 inc VAT)
OEM: 70-3999, E3999
Triumph Crankshaft Sludge / Oil Tube - 350/500cc Unit Twins Circa 1959-74 Crankshaft oil tube, sludge trap - correct fitment on 3TA, 5TA and T100 models...
+

sw086-PREM-B18
£9.95 (£11.94 inc VAT)
OEM: 60-3719, D3719, 19-6508, PS5330/1/03
Triumph Oil Pressure Switch Triumph - Veglia Type With Straight / Parallel Threads As fitted to later T100 + T140, TR7, TSS, TSX, T150 and T160 models...
 

sw085-UK-B18
£9.95 (£11.94 inc VAT)
OEM: PS5320/6, 60-2133, D2133, 19-6504, 5300/1/07
Triumph/BSA Oil Pressure Switch - Smiths Type With Taper Thread As fitted to unit A50, A65, T120, TR6, T90, T100 models circa 1969-73. Also used on some...
+

filt131
£10.95 (£13.14 inc VAT)
OEM: 66-8359
Oil Filter Element - BSA M20, M21, M23, M33, B31, B32, B33, SILVER STAR + GOLD STAR OEM: 66-8359
+

filt840m-B3
£10.95 (£13.14 inc VAT)
OEM: 70-3722, E3722
Oil Sump Filter Gauze - Triumph 350cc + 500cc Unit Twins Conical type, fits 350/500 unit construction models OEM: 70-3722, E3722
+

spring1136-B18
£10.95 (£13.14 inc VAT)
OEM: 67-1136
BSA Cush Drive Spring - Pre Unit A, B, & M Models - 1955-62 Correct for all swinging arm models with a 2 lobe cush drive cam from 1955-62. Made in...
+

studs601-B14
£10.95 (£13.14 inc VAT)
OEM: 21-1865, S1865
Triumph Cylinder Base Stud Set - 650cc Models - Circa 1968-72 Correct fitment on Triumph T120 and TR6 models. Set includes 8 cylinder base studs - 12...
+

studs602-B18
£10.95 (£13.14 inc VAT)
OEM: 21-1865, S1865, 71-3013, E13013
Triumph Cylinder Base Stud Set - 750cc Models - Circa 1973-82 Correct fitment on Triumph T140 and TR7 models. Set includes 8 cylinder base studs - 4x...
+

seal352-B7
£10.95 (£13.14 inc VAT)
OEM: 40-0025, 40-0243, 40-0679, 40-3281, 40-0977
Oil Seal Set - Engine and Gearbox - BSA C15 and B40 Side Points Models - Circa 1964-66 Suitable for C15 and B40 Sport Star models with side points circa...
+

seal361-B7
£11.95 (£14.34 inc VAT)
OEM: E4568, 70-4568, E4578, 70-4578, E3876, 70-3876, E7565, 70-7565, T1956, 57-1956, T946, 57-0946
Oil Seal Set - Engine and Gearbox To suit Triumph T120, TR6, 650cc 1963-1971 Contains: Contact point seals, Clutch back plate seals (for both early and late...
+

seal358-B7
£11.95 (£14.34 inc VAT)
OEM: E4568, 70-4568, E3833, 70-3833, T1956, 57-1956, T946, 57-0946
Oil Seal Set - Engine and Gearbox To suit Triumph T120, T140, TR7 5 Speed, 1972-1983 Contains: Contact point (camshaft) seals, Crank timing side seal,...
+

seal360-B7
£11.95 (£14.34 inc VAT)
OEM: E4568, 70-4568, E3833, 70-3833, E3876, 70-3876, H1478, 57-1478, H2239, 57-2239, E7565, 70-7565
Oil Seal Set - Engine and Gearbox To suit Triumph 3TA, T21, T90, 5TA, T100, TR5T, 350cc, 500cc 1963-1974 Contains: Contact point (camshaft) seal, Crank...
+

seal354-B7
£11.95 (£14.34 inc VAT)
OEM: 57-0946, 68-0027, 68-27, T946, 57-0946, 11268-0026, 11468-0235, 11967-0674, 68-235, 68-0235
Oil Seal Set - Engine and Gearbox To suit BSA A50, A65, 1962-1973 Contains: Contact point (camshaft) seal, Crank seal, Clutch seal, Gearbox seal, Chain case...
+

seal356-B7
£11.95 (£14.34 inc VAT)
Oil Seal Set - Engine and Gearbox To suit Norton Dominator, Atlas, 500cc, 600cc, 650cc, 750cc 1949-1968
+

plug1212-B18
£11.95 (£14.34 inc VAT)
OEM: 67-1212
BSA Large Journal Crankshaft Sludge Trap Plug With Extension - A10 + Early A50 and A65 Models To fit large journal crankshafts as used on pre-unit A10...
+

bolt3575-B14
£11.95 (£14.34 inc VAT)
OEM: 82-3575, F3575
Triumph Gearbox Pivot Bolt - Pre Unit 500/650cc Models Circa 1954-59 Threaded mounting stud, correct fitment on T100, 6T, T110, T120, TR6 models. Length...
+

nut2520-B13
£11.95 (£14.34 inc VAT)
OEM: 65-2520
BSA Engine Sprocket Cush Drive Bearing Nut - B, C and M Group models Circa 1937-54 Correct fitment on all B31, B32, B33, B34, M20, M21 models circa...
+

screwkit-12-B9
£12.95 (£15.54 inc VAT)
OEM: 65-3063, 67-1706, 67-1711, 42-7517, 67-0133, 67-0132, 65-3063
Allen Screw Kit - BSA A7, A10, Swing Arm Model Set of Allen screws to fit the BSA A7 500cc and BSA A10 650cc models with swing arm frame. This kit has the...
+

spring1706-B13
£12.95 (£15.54 inc VAT)
OEM: 66-1706
BSA Cush Drive Spring - B and M Group Models from 1937-54 Correct for all B group models B24, B26,  B31, B32, B33, B3 4 Gold Star  from 1937-54. Also M...
+

filt5230-B3
£12.95 (£15.54 inc VAT)
OEM: 70-5230, 70-4543, D5230, E4543
Triumph Crankcase Oil Sump Filter Early Unit 650cc Models - 1963 Only Crankcase oil filter gauze assembly suitable for early 6T, T120 and TR6 models....
+

seal353t-B7
£12.95 (£15.54 inc VAT)
OEM: E4568, 70-4568, T1956, 57-1956, T3642, 57-3642, D3510, 60-3510, D3500, 60-3500, T3634, 57-3634, T3644, 57-3644
Oil Seal Set - Engine and Gearbox To suit Triumph T150, T160, 1968 - Contains: Contact point seal, Gearbox Seals (5 Speed Option x2), Gearbox final drive...
+

seal353b-B7
£12.95 (£15.54 inc VAT)
OEM: E4568, 70-4568, T1956, 57-1956, T3642, 57-3642, D3510, 60-3510, D3500, 60-3500, T3634, 57-3634, T3644, 57-3644
Oil Seal Set - Engine and Gearbox To suit BSA A75 Contains: Contact point seal, Gearbox Seals (5 Speed Option x2), Gearbox final drive (sprocket) seal,...
+

bear018-V-F4
£12.95 (£15.54 inc VAT)
OEM: 89-3023, 1463-31, 24-4217, 60-3552
BSA/Ariel/Villiers Crankshaft Main Bearing BSA Bantam models crankshaft main bearing BSA Bantam D7 175cc and other models. Camshaft Ariel 1000cc...

fkscrew221-B9
£13.95 (£16.74 inc VAT)
Stainless Steel Allen Screw Kit - Triumph TR6, T120, T140 Triumph 650/750 Unit construction twins (1968-1983) Complete Set, includes allen keys. Stainless...
+

seal357-B7
£13.95 (£16.74 inc VAT)
OEM: 06-2726, 062726, 034053, 048023, NMT272, NMT2187, 040132
Oil Seal Set - Engine and Gearbox To suit Norton Commando 750cc, 850cc, 1968-1975 Includes the valve stem seals 06-2726 OEM: 06-2726, 062726, 034053,...
+

fkscrew226-B9
£13.95 (£16.74 inc VAT)
Stainless Steel Allen Screw Kit - Triumph 500cc & 650cc Pre-unit Twins Triumph 500/650 Pre-unit construction twins Complete Set, includes allen...
+

fkscrew228-B9
£13.95 (£16.74 inc VAT)
Stainless Steel Allen Screw Kit - Triumph T20 Cub side points engine Triumph T20 Cub side points engine Complete Set, includes allen keys. Stainless...
+

bear437-F4
£13.95 (£16.74 inc VAT)
OEM: E9494, 70-9494
Crankshaft Main Bearing. Fits Triumph 500cc Unit Twins, 5TA,T100,TR5 etc timing side (1968-) OEM: E9494, 70-9494
+

screwkit-86-B9
£13.95 (£16.74 inc VAT)
OEM: 14-6608, 14-6609, 14-7023, 14-7020, 21-1878, 14-6620, 57-1553
Posi Drive Screw Engine Screw Kit - Triumph 650cc twins 1969-1970 Triumph 650 Unit construction twins 1969-70 Complete Set, as shown in photo OEM: 14-6608,...
+

cap063-B4
£13.95 (£16.74 inc VAT)
BSA Chaincase Inspection Cap - B & M Group Models BSA Primary Chaincase Inspection Nut - Suit most B and M Models - B31, B32, B33 and M20, M21 Thread...
+

pipe1610-B13
£13.95 (£16.74 inc VAT)
OEM: 83-1610, F11610
Triumph Breather Hose 'T' Piece - 500/650/750cc Unit Twins - 1971-73 Crankcase breather pipe connector for T100 Daytona, T120, TR6, T140, TR7 models...
+

fkscrew211-B9
£13.95 (£16.74 inc VAT)
OEM: 14-6606, 14-6608, 14-6610, 14-6611, 14-6612, 14-6614, 40-0236
Stainless Steel Allen Screw Kit - BSA B50 Models Complete set, includes two allen keys and all required UNC stainless steel hex screws. OEM: 14-6606,...
+

Our dedicated classic trials
and motocross section.
Parts available for British,
Japanese & European models.

.

RENNTEC ENGINEERING
Premium quality British made
motorcycle luggage racks,
grab rails and engine bars.
 
.