.

Feked Classic Bike Parts
The Old Racing Stables, Nine Yews, Cranborne, Dorset BH21 5PW, UK

.
.
.

Useful & Interesting

SHIPPING COSTS SHIPPING COSTS

Engine Upper

oring727H
£0.95 (£1.14 inc VAT)
OEM: 60-3548, 70-3253, E3253
Rocker spindle O Ring for Triumph 200, 350, 500, 650 and 750cc models This o-ring is the little sucker that you replace to stop that oil leak from the...

gask1577
£0.75 (£0.90 inc VAT)
OEM: 70-1577, E1577, 65-5800, E1564, 70-1564, 67-42, 67-0042, NT376
Triumph/BSA Fibre Washer - Sump Base Gasket, Rocker Box Gasket, Inspection Cap Fibre washer used extensively on Triumph and BSA models. Approximately...
+

anti-sump-tap-switch-mag
£54.65 (£65.58 inc VAT)
Anti Wet Sump Oil Pipe Tap With Switch - Magneto or Coil Ignition Systems A solution to a frequent problem of wet sumping. On many of the older classic...
 

seal237
£1.25 (£1.50 inc VAT)
OEM: 70-4752, E4752
Push rod cover tube square section seal for Triumph T120, T140 etc Suit some of the 650cc and 750cc engines Square Section Seal OEM: 70-4752, E4752
+

seal541
£1.25 (£1.50 inc VAT)
OEM: 70-3547, E3547
White silicone push rod 'O' ring Suit some of the 650cc engines Fits the 3TA, 5TA, T100 and other 350/500cc unit engines. Square section o-ring seal OEM:...
+

tapp731
£0.55 (£0.66 inc VAT)
OEM: 70-8782, 70-7563, E8782, E7563
Triumph Tappet Guide Block O Ring - 500/650/750cc Models  OD: 1" (25.4mm) ID: 7/8" (22.3mm) Thickness: 1/6" (1.9mm) Viton Rubber OEM:  70-8782,...
+

washer1335
£0.95 (£1.14 inc VAT)
OEM: 70-1335, E1335, 40-0159, 40-159
Triumph Copper Washer - Overhead Rocker Spindle / Timing Cover Plug Also used for the T140 oil in frame sump washer. OEM: 70-1335, E1335,  40-0159,...
+

gear007H-B4
£4.45 (£5.34 inc VAT)
OEM: 57-2166, 70-8231, E732, 70-0732
Triumph / BSA - Gearbox Inspection Plug / Chaincase Filler Cap - Singles, Twins and Triples BSA all unit singles chain case A50, A65. Triumph 3TA, 5TA,...
+

nut036-B14
£0.75 (£0.90 inc VAT)
OEM: P0172A, S1-52, 21-7052, PO172A, PO-172A, 02-0046
Triumph Twin - Cylinder Base Nut - P0172A Also to secure top head stay to engine. 3/8" CEI OEM: P0172A, S1-52, PO172A, PO-172A, 02-0046
+

seal538
£1.25 (£1.50 inc VAT)
OEM: 70-7310, E7310
Push rod cover tube 'O' ring for Triumph T120, T140 etc Suit some of the 650cc and 750cc engines Also suits some of the later 350/500cc engines (confused? -...
+

wash3751
£0.75 (£0.90 inc VAT)
OEM: 70-3751
Triumph Rocker Cover Inspection Cap Washer Triumph Unit models OEM: 70-3751
+

seal537
£1.25 (£1.50 inc VAT)
OEM: 71-1283
Push rod cover tube 'O' ring for Triumph T120, T140 etc Suit some of the 650cc and 750cc engines O - ring OEM: 71-1283
+

oil-tap3-B3
£15.95 (£19.14 inc VAT)
Wet Sumping, Anti Sump, Oil Pipe Tap A solution to a frequent problem of wet-sumping. On many of the older classic bikes, the oil pump and/or...
+

nut056H-B18
£3.95 (£4.74 inc VAT)
OEM: 70-1435
Triumph T120, TR6 etc Rocker spindle domed nut, as used on all Triumph 500,600cc twins up to (-1968). OEM: 70-1435
+

nut0879-B14
£1.25 (£1.50 inc VAT)
OEM: 82-0879, F879, GS662, 60-4264, 75-0053
1/4" x 26 TPI CEI Nut - Triumph Rocker Box Stud/Oil Tank Mounting + Other Uses Used extensively on many Triumph unit models. Rocker box stud nut on...
+

tapp176-B18
£1.75 (£2.10 inc VAT)
OEM: 71-3748, 40-0167, 99-0067
Valve split cotters - valve collet - Triumph, BSA Triumph 500cc, 650cc, 750cc, T100, T120, T140, T150, T160. BSA 250cc, 750cc, C15, A75 Rocket 3. Price per...
+

seal542
£1.45 (£1.74 inc VAT)
OEM: 70-1496, E1496
Triumph Bottom Push Rod Tube O Ring Seal - 70-1496 Bottom joint washer for various pre unit and unit 650cc twins. OD: 1+1/4" (31.4mm) ID: 15/16"...
+

wash2184
£0.95 (£1.14 inc VAT)
OEM: 82-2184, F2184, NM24252, 02-2138, 71-2598, 01-6213
Triumph / BSA / Norton - 3/8" Thick Plain Washer - Various Uses  As used extensively on various unit models - cylinder head bolts, frame parts + universal...
+

wash1575-B13
£0.75 (£0.90 inc VAT)
OEM: 70-1575, 40-0158, E1575, 40-158
Triumph/BSA Rocker Spindle Thrust Washer - Various Models As used on many BSA models including A7, A10,  A50, A65, B25, B44, B40 and C15. Plus...
+

rod2620-B17
£10.95 (£13.14 inc VAT)
OEM: 70-2620
Triumph Push Rod - 500/650cc Pre Unit and 650cc Unit Models From 1939-73 Correct fitment for all pre-unit Triumph 500/650cc models 5T, T100, 6T, T110,...
+

clip6869-B13
£1.45 (£1.74 inc VAT)
OEM: 70-6869, E6869, 67-0101, WE479, 40-0979
Triumph Piston Gudgeon Pin Circlips (2) - Pre Unit and Unit 500/650cc Models + Unit Singles Gudgeon wristpin circlip - correct fitment on: Pre unit and...
+

tapp0200H-B18
£2.45 (£2.94 inc VAT)
OEM: 97-0200, H200
Triumph Tappet Guide Block Set Bolt - 350/500/650/750cc Models Pre-unit and unit models including 3TA, 5T, 6T, TR5, 5TA, T100, T110, T120, T140. OEM:...
+

nut0103-B14
£0.95 (£1.14 inc VAT)
OEM: 37-0103, W103, 40-3226
1/4" x 26 CEI Nut - Various Uses on Pre Unit and Unit Triumph and BSA Models Used extensively for many applications including cylinder head, manifold...
+

pipe3655-F3
£3.95 (£4.74 inc VAT)
OEM: 82-3655, 82-3182, F3655, F3182
Triumph Oil Filter Union Nut and Connector Pipe - Pre Unit and Unit Models - 1954 Onwards Pipe locates between the rubber oil feed pipe and the oil...
+

rocker-006W-B4
£6.95 (£8.34 inc VAT)
OEM: 70-1564, E1564, 40-0968
Triumph Pre Unit Rocker Box Inspection Cap and Crankcase Filter / Sump Plug on Unit 350/500cc Models Rocker cover inspection cap on 500/650cc pre unit...
 

wash9554
£0.35 (£0.42 inc VAT)
OEM: 70-9554, E9554
Triumph Intake Manifold Carburettor Insulating Rubbber Washer - 650/750cc Unit Twins Carburettor mounting washer to fit T120, TR6, T140, TR7 models from...
+

nut0400-B18
£1.95 (£2.34 inc VAT)
OEM: 97-0400, H400
Triumph Rocker Oil Feed Domed Nut - Unit 350/500cc Models Circa 1959-71 + T20 Tiger Cub Rocker oil feed line acorn nut - correct fitment on 3TA, 5TA, T90...
+

rod4008-B17
£3.95 (£4.74 inc VAT)
OEM: 70-4008
Triumph T100/5TA Engine Pushrod As fitted to all 500cc Unit construction Twins (1958-74) Length approx 120-125mm Made in England by LF Harris OEM:...

wash1574-B13
£1.45 (£1.74 inc VAT)
OEM: 70-1574, E1574, 67-0062, 40-0156, 67-62, 40-156, 06-7698, D12/950, NM18103
Triumph/BSA/Norton Rocker Spindle Thackeray Spring Washer - Various Models Double coil spring thackeray washer - locates on the rocker spindle shaft. As...
+

valv255-B17
£17.95 (£21.54 inc VAT)
OEM: 70-4221, 70-7400, 99-7037, E4221, E7400
Valve Spring Set - Triumph T120, T140, TR6, TR7 650cc, 750cc Twin (1963-) OEM: 70-4221, 70-7400, 99-7037, E4221, E7400
+

wash9555
£0.95 (£1.14 inc VAT)
OEM: 70-9555, E9555
Triumph Intake Manifold Carburettor Cupped Washer - 650/750cc Unit Twins Carburettor mounting washer to fit T120, TR6, T140, TR7 models from 1970-78....
+

clip732m-B18
£1.25 (£1.50 inc VAT)
OEM: 70-3209
Valve Guide Circlip as fitted to Triumph T140, T100, T20 and BSA C15 models. OEM: 70-3209
+

seal1707
£3.95 (£4.74 inc VAT)
OEM: 71-1707, E11707
Triumph Push Rod Tube Collar / Sleeve - 500/650/750cc Twins From 1971 Onwards Zinc plates steel pushrod seal collar - locates between the tappet guide...
+

nut2016-B14
£3.95 (£4.74 inc VAT)
OEM: 21-2016, S2016, 60-3761, D3761, 21-0549, S549
Triumph Con Rod Big End Nut - Unit 650cc Twins + T150, TR25W and BSA B25 Models - Circa 1969-73 Self locking connecting rod nut - correct fitment on T120,...
+

pipe4159
£21.95 (£26.34 inc VAT)
OEM: 70-4159, E4159, 70-3082, E3082, 70-6349, E6349
Triumph T120/TR6, 650cc Rocker Oil Feed Pipe Available as standard or UK made - please select option. Can be used instead of 71-2428, E12428, 70-6349,...

wash1330-B13
£0.75 (£0.90 inc VAT)
OEM: 70-1330, 40-0157, E1330, 40-157
Triumph / BSA Rocker Spindle Thrust Washer - Various Pre Unit and Unit Models Correct fitment on pre unit and unit models - singles, twins and triples...
+

valve011-B22
£16.95 (£20.34 inc VAT)
OEM: E2904, 70-2904
Triumph 650/750cc Exhaust Valve - 70-2904 Exhaust Valve 6T/T120/T140 (1955-83) (Alpha Valve no.V24) Head Diameter: 1.437 Stem Diameter: 0.3095 Length:...
+

pipe3805-224
£23.95 (£28.74 inc VAT)
OEM: 70-7576, E7576, 70-3805, E3805, 70-6351, E6351
Triumph Rocker Oil Feed Pipe - 350/500cc Unit Models - 1957 Onwards A rocker oil feed pipe and banjo assembly to fit 350/500cc unit twins. Designed to...
+

vguide3208t
£9.45 (£11.34 inc VAT)
OEM: E3208, 70-3208, G461
Triumph Inlet / Exhaust Valve Guide - T20 Tiger Cub + 350/500cc Twins Circa 1957-66 - Standard or Oversize Suitable for both inlet and exhaust on many...

nut4264-B14
£0.95 (£1.14 inc VAT)
OEM: 60-4264, GS662, D4264
1/4" x 26 TPI CEI Nut - Triumph Rocker Box Stud/Oil Tank Mounting + Other Uses Used extensively on many Triumph unit models. Rocker box stud nut on...
+

clip238H-B18
£1.45 (£1.74 inc VAT)
OEM: 70-4671, E4671
Triumph Unit models Rocker cover inspection Cap Spring Retaining Clip OEM: 70-4671, E4671
+

push4746
£1.05 (£1.26 inc VAT)
OEM: 70-4746
Triumph Push Rod Steel Washer Steel cup, T90, T100, T120, T140, T150 OEM:  70-4746
+

seal1497
£1.25 (£1.50 inc VAT)
OEM: 70-1497, 70-3547, E1497, E3547
Triumph Push Rod Tube Top Seal - Fibre Type - 350/500/650cc Pre Unit and Early Unit Twins Fibre upper push rod joint washer as used on various models...
+

smallend134-B8
£12.95 (£15.54 inc VAT)
OEM: 6-0492, SE13
BSA Singles Small End Bearing - 66-0492 B31, B32, B33, B34, B40, SS90, B44, B50, M33, M22, M23, M24 (1937-66) Small end bush, piston pin bush, gudgeon pin...
+

tappet3059R-LFH
£39.95 (£47.94 inc VAT)
OEM: 71-7008, 70-3059, E17008, E3059, 70-3059R, 71-7644, E3059R, E17644
Triumph Cam Follower Tappet - 500/650/750cc Pre Unit and Unit Models - Exhaust and Inlet Single cam follower, sits in the tappet block and follows the...
 

capNT367-B4
£13.45 (£16.14 inc VAT)
OEM: NT367, 99-3544
Triumph Primary Chaincase Filler/Inspection Cap - Pre Unit Models Circa 1939-62 Cast alloy chaincase oil filler plug embossed with 'USE LIGHTOIL -...
+

plug5343-B13
£1.95 (£2.34 inc VAT)
OEM: 82-5343, F5343
Triumph Oil Tank Drain Plug - Unit Pre OIF Twins and Triples From 1963 Onwards Oil tank drain plug as used on pre OIF unit T100, T120, TR6, T150 models....
+

rocker010-B4
£16.95 (£20.34 inc VAT)
OEM: 70-4610
Chrome Triumph Rocker Cover Caps - set of 4 Suitable for Triumph. Unit Triumph. Complete with washers. Thread diameter approx 1+3/16" (30mm) OEM: 70-4610
+

rings037
£35.95 (£43.14 inc VAT)
OEM: R11050, E6864, E6865, 70-6864, E6865
Pair of Hepolite Piston Rings for Triumph T120 650cc models etc (1959-75). Supplied as 2 set of Hepolite Piston Rings. Bore Size : 71mm Standard, available...

studset426-B14
£9.95 (£11.94 inc VAT)
OEM: 70-2980, E2980, 31-0222, 70-8012, 70-3302, 82-0879, F879
Triumph Rocker Box Stud and Nut Set - 650cc Unit Models Circa 1963-70 Rocker box to cylinder head - six studs, washers and nuts. Correct fitment on 650cc...
+

pist3958
£119.95 (£143.94 inc VAT)
OEM: 70-3958, E3958, CP172
Triumph T20 Tiger Cub Piston - 9.1 Compression Ratio - Various Models Circa 1959-68 - Gandini/GPM Supplied as 1 piston, complete with rings, gudgeon pin...

nut2922-B14
£1.95 (£2.34 inc VAT)
OEM: 70-2922, 70-1530, E2922, E1530
Conrod Big End Nut - Triumph Pre Unit and Unit 250/500/650cc Singles and Twins - Circa 1946-70 Self locking connecting rod nut - correct fitment on pre...
+

oilcap9659-B4
£28.95 (£34.74 inc VAT)
OEM: 82-9659, F9659, 68-8368
Triumph/BSA Oil Tank Filler Cap with Dipstick - Unit 500/650cc Twins + B25, B44 and T150 Models Complete cap and dipstick assembly - 2" chrome plated...
+

seal3758
£1.25 (£1.50 inc VAT)
OEM: 70-3758, E3758
Triumph Push Rod Seal - Bottom To fit 5TA, 3TA, T100A models from 1957-1963 OEM 70-3758, E3758
+

tapp9352-B13
£21.95 (£26.34 inc VAT)
OEM: 70-9352
Triumph 500cc, 650cc, 750cc, T100, T120, T140 inlet tappet guide block. OEM: 70-9352
+

pipe551-B3
£39.95 (£47.94 inc VAT)
OEM: 42-8346, 42-8347
BSA A7, A10 armoured oil feed pipes Exact replica of genuine pipes Comes as 2 pipes, approx 17" and 18" long, ready to fit OEM: 42-8346, 42-8347
+

pipe248
£21.95 (£26.34 inc VAT)
OEM: 42-0048, 42-48
BSA A7, A10 Rocker oil feed pipe complete. Ariel Huntmaster 650cc Also BSA B31, B33 swing arm models pipe diameter: 3/16" OEM: 42-0048, 42-48
+

pist037
£82.95 (£99.54 inc VAT)
OEM: 70-6868, E6868, 17844
Pair of Hepolite Pistons for Triumph T120 650cc models etc (1959-75). Supplied as 2 Pistons, complete with Hepolite rings, gudgeon pins and circlips. Bore...

clip425-B18
£1.95 (£2.34 inc VAT)
OEM: 70-4609, E4609
Triumph T120, TR6 models Rocker cover inspection Cap Spring Retaining Clip OEM: 70-4609, E4609
+

bolt742-B14
£23.95 (£28.74 inc VAT)
Triumph High Tensile 9 piece Cylinder Head Bolt Set for TR6/T120 Unit models. Suit most later Triumgh twin 650cc 1x 70-4771 Centre head bolt - 5/16" x 3" x...
+

piston9488
£99.95 (£119.94 inc VAT)
OEM: 70-9488, 70-6868
Harris Pistons for Triumph T120/TR6 650cc - 70-9488 Pair of high quality pistons, Made in England by LF Harris. Includes the pistons, Gudgeon pin, Ring...

bolt2982-B19
£2.45 (£2.94 inc VAT)
OEM: 70-2982, E2982
Triumph Rocker Box Corner Bolt - Pre Unit and Unit Alloy Head 500/650cc Models Circa 1952-68 Correct fitment on pre unit TR5 and T100 models circa...
+

bolt553-B18
£3.45 (£4.14 inc VAT)
OEM: 65-0317
BSA A7, A10 Rocker spindle oil feed bolt OEM: 65-0317

pist-16945
£39.95 (£47.94 inc VAT)
OEM: 40-0970, 70-7998, E7998, 16945
Hepolite Piston - BSA/Triumph Unit Singles - B25, C25, TR25 Models Circa 1967-71 Suitable for 250cc singles with the square alloy barrel - B25, C25 and...

tapp9353-B13
£29.95 £19.95 (£23.94 inc VAT)
OEM: 70-9353
Triumph 500cc, 650cc, 750cc, T100, T120, T140 exhaust tappet guide block. OEM: 70-9353
+

valv256-B17
£15.95 (£19.14 inc VAT)
OEM: 70-4011, 70-5946, E4011
Valve Spring Set - Triumph 350/500cc Unit Models - 1966 Onwards Correct fitment on 3TA, T90, 5TA and T100 models circa 1966-73. OEM: 70-4011,...
+

stud2962-B13
£1.95 (£2.34 inc VAT)
OEM: 70-2962, E2962
Triumph - Inlet Manifold To Carburettor Stud - 500/650cc Twins from 1952-69 Length: 1+1/4" (32mm) Diameter: 5/16" (7.7mm) BSW/CEI threads OEM:...
+

wash3302
£0.25 (£0.30 inc VAT)
OEM: 70-3302, E3302, 75-0214, 75-214, S21/91
Triumph / BSA - 1/4" Thin Plain Washer - Various Uses on Unit Models As used on various unit models - rocker box studs, engine shields + universal use as...
+

seal3391
£1.95 (£2.34 inc VAT)
OEM: 70-3391, E3391, 40-0180, 40-180
Triumph/BSA Push Rod Tube Seal - Bottom - T20 Tiger Cub + C15 Models Circa 1954-67 Lower push rod tube oil joint washer as used on all T15 and T20 models...
+

nut066M-B14
£2.95 (£3.54 inc VAT)
OEM: 67-1537
BIG END NUT - BSA A7, A10 500cc, 650cc Connecting rod, con rod, con-rod, big end nut, bearing shell nut. OEM: 67-1537
+

rings035
£35.95 (£43.14 inc VAT)
OEM: R26490
Pair of Hepolite Piston Rings for Triumph T140/TR7 750cc models (1972-). Supplied as 2 set of Hepolite Piston rings. Bore Size : 76mm Standard, available...

valve2900
£9.45 (£11.34 inc VAT)
OEM: E2900, 70-2900, G424
Triumph Exhaust Valve Guide - Pre Unit 500/650cc Models Circa 1946-66 - Standard or Oversize Correct fitment on 5T models circa 1946-59,  TR5 models...

tapp470-B18
£1.25 (£1.50 inc VAT)
OEM: 70-0470
Hexagonal Tappet Nut- Triumph T120/T140 and BSA A7/A10 OEM: 70-0470 CEI thread Made in England
+

rocker2079-B4
£1.95 (£2.34 inc VAT)
OEM: 71-2079, E12079
Triumph Rocker Box Inspection Plug - 500/650cc Unit Twins From 1971 Onwards Threaded alloy tappet access cap - correct fitment on T100, T120 and TR6...
+

tappet8801-LFH
£38.95 (£46.74 inc VAT)
OEM: 70-8801, E8801
Triumph Exhaust Cam Follower Tappet - 650/750cc Unit Twins - Circa 1968-1980 Single exhaust tappet / cam follower with oil hole, sits in the tappet block...
 

bolt014-B19
£8.95 (£10.74 inc VAT)
OEM: 70-6576, 21-2016, 70-2490, E2490, E6576
BIG END BOLT - Triumph Triumph Big end bolt, T120/TR6/6T and others Thread:  5/16" UNF -  24 TPI Note - the correct nut that fits this is 60-3761 see link...
+

valve2899
£9.45 (£11.34 inc VAT)
OEM: E2899, 70-2899, E1480, 70-1480, G420
Triumph Inlet Valve Guide - Pre Unit 500/650cc Models Circa 1946-66 - Standard or Oversize Correct fitment on 5T models circa 1946-59, TR5 models circa...

valve094-B22
£16.95 (£20.34 inc VAT)
OEM: E4603, 70-4603
Triumph 650cc/750cc Inlet Valve - 70-4603 Triumph T120 Bonneville (1963-72) TR6 from Eng. No. (1966-72) Inlet Valve (Alpha valve no.V245) Also for T140...
+

vguide3828
£11.95 (£14.34 inc VAT)
OEM: 70-3828, E3828, G424PB
Triumph Exhaust Valve Guide - T120 Bonneville Models Circa 1959-72 - Standard or Oversize Length: 2+9/32", 2.27" (57.7mm) Available as standard, +.002...

vguide3827
£11.95 (£14.34 inc VAT)
OEM: 70-3827, E3827, G420PB
Triumph Inlet Valve Guide - T120 Bonneville Models Circa 1959-72 - Standard or Oversize Length: 1+31/32", 1.97" (50.1mm) Available as standard, +.002...

seal7363-B13
£1.95 (£2.34 inc VAT)
OEM: 60-7363, 06-2726, D7363, 062726
Valve Guide Oil Seal - Triumph/Norton - 60-7363, 06-2726 Inlet valve guive valve seal, as fitted to Triumph T140, Norton Commando and other models Valve...
+

nut0449-B14
£0.50 (£0.60 inc VAT)
OEM: 02-0449
3/8" CEI Nut - BSA Rocker Spindle / Timing Cover / Brake Cam Nut 3/8" x 26 CEI Thin OEM: 02-0449
+

seal3540
£2.25 (£2.70 inc VAT)
OEM: 70-3540, E3540
Triumph Push Rod Tube Seal - Top - T20 Tiger Cub Models Circa 1954-67 Upper push rod tube oil joint washer as used on all T15 and T20 models from 1954...
+

piston-rings6893/4
£37.95 (£45.54 inc VAT)
OEM: 70-6893, 70-6894, E6893, E6894, R13570
Pair of Harris Piston Rings for Triumph 500cc T100 Models - Circa 1958-74 Supplied as a full sets of piston rings - 2x top compression rings, 2x second...

fkcap029-F2
£22.95 (£27.54 inc VAT)
OEM: 90-8035
2" Vented Petrol or Oil Tank Filler Cap - Chrome Plated 2" fuel/oil cap with offset vent - push turn fit and integral cork seal. Will fit most oil tanks...
+

valv227-B17
£13.95 (£16.74 inc VAT)
OEM: VS510, 99-3700, E1487, E1488, 70-1487, 70-1488
Valve Spring Set - Triumph 5T, TR5, T100, 6T, TR6, T110 (racing models) & T120 (1959-60). 8 Springs. Terry No VS510 Includes 4 outer springs and 4...
+

valvecollar1543-B13
£5.45 (£6.54 inc VAT)
OEM: 70-1543, E1543
Triumph Valve Spring Top Collar - 650/750cc Twins - 1963-82 Triumph various models, valve spring retaining collar, sits on top of the valve spring with...
+

wash2080-B13
£1.95 (£2.34 inc VAT)
OEM: 71-2080, E12080
Triumph Rocker Box Inspection Plug Copper Washer - 500/650cc Unit Twins From 1971 Onwards Folded copper washer for use with the threaded alloy tappet...
+

tapp1513A-B13
£4.95 (£5.94 inc VAT)
OEM: 70-1513, E1513, 67-0056, 67-56
Triumph/BSA Mushroom Head Tappet Adjuster - Pre Unit + 650/750cc Unit Twins + A7 and A10 Models - 1946 On Rocker adjusting pin with mushroom head and hex...
+

nut0550-B18
£2.95 (£3.54 inc VAT)
OEM: 21-0550, S550
Triumph Rocker Oil Feed Dome Nut - 750cc Twins and Triples From 1969 Onwards Chrome plated rocker spindle / oil feed pipe domed acorn nut - correct...
+

vvg424
£99.95 (£119.94 inc VAT)
OEM: 70-3827, 70-3828, 70-4603, 70-2904
Triumph T120 (1963-72), TR6 (1966-72) 650cc, Complete Valve guide set. To Engine No. DU44394 Includes Bronze guides, and valves. Valve Guides : Set of 4...
+

pipe249
£21.95 (£26.34 inc VAT)
OEM: 40-0183, 40-183, 47-8397, 41-0807, 41-807
BSA Rocker Oil Feed Pipe - C15, B25, B40, B44, B50 Models A rocker oil feed pipe and banjo assembly to fit many of the BSA unit singles. Designed to be...
+

bolt401-B19
£1.95 (£2.34 inc VAT)
OEM: 14-1401
Triumph 650cc Twin - Cylinder Head Stud - 14-1401 Also fits some of the T140 750cc UNF & UNC OEM: 14-1401
+

smallend1511-B8
£13.95 (£16.74 inc VAT)
OEM: 70-1511, SE106, E1511
Triumph 500/650 Small End Bearing - 70-1511 5T, T100, TR5, 6T, T110, TR6, T120 (1946 -) Small end bush, small end bearing. OEM: 70-1511, SE106, E1511
+

stud2813
£3.25 (£3.90 inc VAT)
OEM: 71-2813, E12813
Triumph - Inlet Manifold Stud - 650/750cc Unit Twins - 1972-78 Suitable for 650/750cc Unit Twins from 1972-78 with bolt-on inlet manifolds Overall...
+

pist278r
£44.95 (£53.94 inc VAT)
OEM: R17350
Set of Hepolite Piston Rings for BSA A65 650cc models etc (1962-73). Supplied as Hepolite Rings for 2 Pistons. Bore Size : 75mm Standard, available as STD,...

In 2017 we launched our
dedicated classic trials and
motocross section after buying
Sammy Miller Products.

We are pleased to announce
that we have recently
acquired TYOFFROAD.

.